In short:
- Most glass shopfront doors have a slim aluminium frame with a mortice deadlock or hook lock built into the narrow stile beside the glass.
- The commonest "lock" fault is the bolt no longer lining up with its keep because the door has dropped or the closer is out of adjustment.
- Parts are size-specific: backset, case depth and cylinder type all have to match the stile.
- If a roller shutter sits in front of the shopfront, its lock, springs and motor are part of the same daily routine. We work on those too.
How a shopfront door is put together
A typical shopfront door is a sheet of glass in an aluminium frame. The vertical frame members (stiles) are slim, so the lock has to be slim too. Trade write-ups on storefront doors describe narrow-stile mortice deadlocks in three standard backsets, with a long pivoting bolt that can bridge a larger gap between the door and the jamb. Hook bolts are used where the door slides, and some hook-bolt cases are made for both swinging and sliding commercial aluminium doors.
In practice in a shop you'll meet:
- A narrow-stile deadlock operated by a key outside and a key or thumb-turn inside.
- A hook lock on sliding or bi-parting doors, where the bolt swings up and hooks into the keep.
- A floor spring or overhead closer. Floor springs sit in the floor under the door and close it; dormakaba, for example, makes one specifically for aluminium and toughened glass doors. They're relevant here only because they decide where the door stops, and so whether the bolt meets its keep. Our work is the lock.
Common faults and their usual causes
| Symptom | Usual cause |
|---|---|
| Key turns only when you push or pull the door | The bolt is rubbing on the keep: the door has dropped, or the closer stops it short of the frame |
| Key won't go in or won't turn at all | Worn or dirty cylinder, damaged key, or something pushed into the keyway |
| Bolt throws but the door still opens | Bolt missing the keep, or the keep has come loose from the frame |
| Thumb-turn inside spins freely | Broken tail or cam on the cylinder, or a stripped connection to the lock case |
| Cylinder face loose or turning in the door | Cylinder retaining screw or ring has worked loose |
| Rough, gritty action and white powder on the aluminium | Corrosion, typical of shopfronts that take sea air and road grime |
Shopfronts close to the sea get salt as well as street dust. ASSA ABLOY's care guide asks for shorter maintenance intervals in marine environments; more in corroded locks near the sea.
Safe checks at opening or closing time
- Look at the gap between the door and frame along the lock side. Uneven gaps mean the door has moved.
- Check the door closes fully on its own. If it stops short, the bolt can't reach the keep.
- Try the spare key before assuming the cylinder has failed.
- Look into the keyway with a torch for chewing gum, paper or grit. Don't dig at it with metal.
- With the door open, turn the key or thumb-turn. If the bolt moves freely in the open position, the lock is fine and the fault is alignment.
What makes it worse
- Pulling hard on the door while turning the key. Glass doors are heavy, and the force goes through the bolt and the cylinder.
- Adjusting a floor spring yourself. Floor springs and closers have their own adjustment and specialist service; get a door closer technician for those.
- Leaving the shop on the shutter alone because the door lock is playing up. Have both working.
- Glue or tape in a keyway to "stop it rattling". It ends in a seized cylinder.
- Buying a lock by look. Narrow-stile locks come in different backsets and case depths; a lock that looks the same may not fit the stile.
Roller shutters in front of the shopfront
Many shops close with a roller shutter over the glass. Shutters are one of our normal services: locks, mechanisms, springs, shutter motors and gate motors. Common complaints are a shutter that sticks in its guides, a lock or padlock point that won't line up, or a motor that hums and doesn't move.
The makers' advice is clear on what owners should and shouldn't do. Trellidor's care guide says to keep the slats and guides clean, not to spray lubricant into the motor and not to try to clean the motor inside the shutter box. ASSA ABLOY's roller shutter maintenance page notes that regular inspection catches wear, corrosion and mechanical issues early and checks that safety features work. If a shutter is jammed half-open, don't force it down by hand; call for help.
Repair or replace?
Realigning the door, tightening or moving a keep, or replacing a worn cylinder are typical repairs, covered by our lock repair service. Replacement is the better answer when the lock case is broken, corrosion has seized it, the model can't be matched, or the door was forced. See lock replacement for that. The technician measures the stile, backset and cylinder on site and quotes before any work starts.
When to call us, and what to send
Shops can't wait for the lock to sort itself out. Our commercial locksmith service covers shopfronts, offices, restaurants and studios, and we're open 24/7, so a door that won't lock at closing time is a normal call. If staff can't get in at opening time, read locked out of your café or restaurant at opening time.
- Photos of the door from outside and inside, the lock edge and the keep in the frame.
- Any make stamped on the lock face or cylinder.
- Whether there's a roller shutter, and whether it's manual or motorised.
- Proof that you own or run the business, such as ID with a lease or a company letter.
- If the shop is in a centre or office block, let centre or building security know a locksmith is coming.
The R350 call-out fee. The technician assesses the job on site and gives you the price before any work starts. Nothing is done until you agree. Payment is by EFT, cash or card. Shopfronts are concentrated in the business areas, so this applies whether you need a locksmith in the Cape Town CBD, a locksmith in Woodstock or a locksmith in Salt River. For everything else, see our mobile locksmith in Cape Town homepage.
Questions
Can you fix the floor spring as well?
Floor springs and door closers are specialist hardware with their own makers' service. We focus on the lock, and we'll tell you if the closer is what's stopping the door lining up.
The key works but only if I lift the door. What's wrong?
The door has most likely dropped, so the bolt sits low against the keep. That's an alignment problem. Forcing the key wears the cylinder and can snap the key, so have it adjusted.
Can you copy the shop keys for my staff?
No, we don't do key cutting or key duplication. If you're worried about how many keys are out there, a new cylinder or lock with a fresh set of keys is an option we can quote for on site.
Need a locksmith to look at it?
If this hasn't solved the problem, our commercial locksmith service covers it. We're a mobile locksmith in Cape Town, so we come to your door. Areas where this comes up often include Cape Town City Centre, Woodstock, Salt River.
Sources and further reading
- Locksmith Ledger: An overview of aluminium stile glass storefront doors — Narrow, medium and wide stiles; mortice deadlocks in three standard backsets; long pivoting bolt bridges larger door-to-jamb gaps; hookbolts for sliding doors; pivots used with concealed closers in the floor or header.
- Lock and Key: ALPRO Euro mortice hookbolt case datasheet — Hookbolt deadlock for narrow-stile aluminium doors, for swinging and sliding commercial doors; takes euro cylinders; offered in different backsets and case depths.
- dormakaba: BTS 84 floor spring — Floor spring developed for the aluminium and toughened glass door industries, for double-action doors.
- Trellidor: Roller shutters care guide — Clean slats and guides; do not spray lubricant into the motor or clean the motor inside the shutter box; salt-related corrosion near the sea.
- ASSA ABLOY Ireland: Maintenance for roller shutters — Regular inspection identifies wear, corrosion and mechanical issues early and ensures safety features work.
- ASSA ABLOY South Africa: Product care and maintenance — Shorter maintenance intervals in marine environments.
- Property24 (Cape Town City Centre, Salt River) and Wikipedia (Woodstock) — Woodstock zoning mixes residential, commercial and light industrial use, with shops and offices in converted warehouses; Property24 lists 51 commercial properties in the City Centre and 19 commercial or industrial in Salt River (https://www.property24.com/for-sale/cape-town-city-centre/cape-town/western-cape/9138, https://www.property24.com/for-sale/salt-river/cape-town/western-cape/10158).