In short:
- Airborne salt settles on handles, cylinders and padlocks. ASSA ABLOY says salt deposits can damage both the surface and the mechanism, and must be removed regularly.
- Maintenance should be more frequent near the sea. Trellidor ties its roller shutter cleaning intervals to distance from the beach.
- Follow your lock maker's care guidance. Makers recommend different products, and the wrong one can gum up a lock.
- For hardware within about five kilometres of the surf, the Australian Stainless Steel Development Association recommends Grade 316 stainless steel as a minimum.
- A gritty key is an early warning. Deal with it before it snaps in a seized lock.
Why locks near the sea corrode
Wind carries fine droplets of sea water inland. When they dry, they leave salt on every exposed surface: door furniture, cylinder faces, padlock bodies, gate locks, the screws holding them on. Salt attracts moisture, so the surface stays damp for longer, and corrosion gets going.
ASSA ABLOY's care guidance spells this out. It says dirt, grime and airborne salt deposits can damage a product's surfaces and its mechanism, including the cylinder barrel, and must be removed regularly. It recommends inspecting and cleaning at least once a year, and more often in marine or other corrosive environments.
The Australian Stainless Steel Development Association (ASSDA) notes that tea staining, the brown discolouration you see on stainless steel near the coast, is most common within about five kilometres of the surf and gets worse the closer you are. Wind can carry it further.
Signs your lock is suffering
| What you notice | What's probably going on |
|---|---|
| The key feels gritty or rough going in and out | Salt and dirt building up at the keyway and inside the cylinder |
| The key turns, but the bolt moves sluggishly | Corrosion on the bolt or inside the lock body |
| White or green crust on brass, or rust running from screws | Surface corrosion that will spread if left |
| Brown spots on stainless handles | Often tea staining, which ASSDA describes as cosmetic |
| A padlock shackle that won't spring open | Salt and grit inside the padlock body |
| A sliding or balcony door lock that no longer engages | Corroded hook bolt or keeper, or a door that's dropped on its rollers |
| A keypad lock that misbehaves | Possible moisture or corrosion at battery contacts (check the maker's manual) |
Safe cleaning: what lock makers say
Start with the outside of the lock. ASSA ABLOY's care guide recommends:
- a dilute solution of mild liquid detergent in warm water, not hot;
- a soft-bristle brush, and no abrasive tools;
- a thorough rinse with fresh water afterwards;
- keeping cleaning fluids out of the lock and cylinder;
- no strong solvent cleaners, and no metal polish like Brasso on lacquered brass, which strips the lacquer.
ASSDA makes a related point about stainless steel: washing removes salt deposits, and sheltered areas that rain doesn't wash are particularly prone to staining. That's why the underside of a handle or the inside of a covered porch can look worse than the parts exposed to weather. ASSDA suggests washing stainless steel whenever you wash the windows nearby.
Lubricants: why there's no one-size answer
It's tempting to reach for whatever spray is in the garage. Don't, unless it's what your lock maker recommends. Lock makers give specific instructions for their own products, and those instructions differ.
- ASSA ABLOY's guide recommends a small amount of graphite powder on the key blade for key cylinders, lever locks and padlocks, at least once a year or when the key starts to feel rough.
- For exposed mechanisms, the same guide prefers a Teflon-based lubricant, with light sewing-machine oil as an alternative, used sparingly.
- It warns that too much lubricant collects dust and shortens the life of parts, and that silicone-based lubricants go tacky and can affect how components work.
- Other makers specify their own products for their own locks, and what suits one design may not suit another.
The safe rule is to check the paperwork or the maker's website for your lock and follow that. If you don't know who made the lock, a photo of the cylinder face and the edge of the door usually tells a locksmith.
Choosing hardware for a sea-facing home
If you're replacing corroded locks or fitting out a new home near the water, material choice matters more than looks.
| Question | Why it matters |
|---|---|
| Is the stainless steel Grade 316? | ASSDA recommends 316, or a grade with equivalent corrosion resistance, as a minimum within about five kilometres of the surf. |
| How smooth is the finish? | ASSDA says smoother surfaces resist tea staining better. |
| What corrosion grade does it carry? | European standard EN 1670 classifies building hardware for corrosion resistance. Ask the supplier which grade a product has been tested to. |
| Is it plated or solid? | ASSA ABLOY's care guide says soft finishes such as plating and lacquered brass need special care, and that polish strips lacquer. |
| Do the screws match? | A handle is only as durable as the screws holding it on. Ask for fixings suited to the same environment as the hardware. |
Our lock replacement service covers swapping tired coastal hardware for something better suited. The technician quotes on site, before anything is fitted.
Shutters, gates and padlocks
Security gates, roller shutters and padlocks take the worst of the weather. Trellidor's roller shutter care guide ties cleaning frequency to distance from the beach: every one to two weeks within 500 metres, every two to four weeks between 500 metres and one kilometre, every two to three months from one to 10 km, and every six months further away. It recommends a salt-free car wash liquid, warns against abrasive, detergent-based and solvent cleaners on its shutters, and says not to spray lubricant into the motor.
Notice that this is different from ASSA ABLOY's advice for door hardware. That's exactly why the maker's own guidance should decide what you use. We repair roller shutter locks, mechanisms, springs and motors, and gate motors, as everyday work.
What makes corrosion damage worse
- Forcing a gritty key. Keys snap in seized locks, and then you need broken-key extraction as well as a repair.
- Hammering or levering a stuck bolt or padlock shackle.
- Using abrasive pads or metal polish on plated or lacquered finishes.
- Soaking the lock in whatever's to hand. Thick or sticky products trap salt and grit inside.
- Waiting until it seizes. A lock that's cleaned and looked after early often needs only a service; one that has seized solid may need replacing.
Strong wind adds its own wear to coastal doors. See when strong wind slams doors.
When to call a locksmith, and what to send
Call when the key is getting hard to turn, when a bolt or latch no longer moves freely, or when a padlock or gate lock is close to seizing. Our lock repair service covers cleaning, servicing and repairing corroded locks, and replacing what can't be saved.
- Photos of the cylinder face, the handle and the edge of the door.
- Any brand or markings you can see.
- Which way the door faces and how exposed it is.
- Roughly how old the lock is and when it was last serviced.
- For sliding and balcony doors, a photo of the lock and the keeper on the frame.
R350 call-out fee. The technician assesses the job on site and gives you the price before any work starts. Nothing is done until you agree. Payment is by EFT, cash or card, and we're open 24/7. Find out more on our Cape Town mobile locksmith homepage.
Questions
My stainless steel handles have brown spots. Are they failing?
Probably not. ASSDA describes tea staining as cosmetic: it doesn't affect structural integrity. Regular washing with fresh water and a mild detergent helps. If the handle or lock is also getting stiff, that's a different issue worth having checked.
How often should I service locks near the sea?
ASSA ABLOY recommends at least once a year in general, more often in marine environments, and lubricating key cylinders whenever the key feels rough. Your own lock maker's guidance comes first.
Can you replace corroded locks with marine-grade ones?
Yes, lock replacement is part of what we do. The technician looks at the door and the existing hardware, talks through suitable options, and quotes on site before fitting anything.
Need a locksmith to look at it?
If this hasn't solved the problem, our lock repairs service covers it. We're a mobile locksmith in Cape Town, so we come to your door. Areas where this comes up often include Sea Point, Clifton, Camps Bay, Llandudno, Hout Bay.
Sources and further reading
- ASSA ABLOY South Africa: Product Care and Maintenance — Airborne salt damages surfaces and mechanisms including the cylinder barrel; shorter maintenance intervals in marine environments; mild detergent and fresh-water rinse; keep fluids out of cylinders; graphite for cylinders, Teflon-based lubricant for exposed parts, no silicone; Brasso strips lacquer.
- ASSDA: Preventing coastal corrosion (tea staining) — Tea staining is cosmetic, most common within about 5 km of the surf; Grade 316 as a minimum; smoother finishes; washing removes salt; sheltered areas not rain-washed are particularly susceptible.
- Trellidor: Roller shutters care guide — Cleaning intervals by distance from the beach; salt-free car wash liquid; no abrasive, detergent or solvent cleaners; no lubricant in the motor.
- BSI Knowledge: BS EN 1670:2007 Building hardware. Corrosion resistance. Requirements and test methods — The current European standard for classifying building hardware by corrosion resistance.
- Wikipedia: Sea Point — Beachfront promenade; apartment buildings toward the beachfront.
- Wikipedia: Clifton, Cape Town — Atlantic Seaboard suburb with four beaches.
- Wikipedia: Camps Bay — Atlantic Seaboard suburb on the coast with a large beach.
- Wikipedia: Llandudno, Cape Town — Seaside suburb on the Atlantic Seaboard.
- Wikipedia: Hout Bay — Sheltered bay with a beach and a fishing harbour.